2sqm Carbon Film Underfloor Heating, Wood & Laminate Kits. Underfloor Heating Film Kits Designed for use as either the Primary Heat source, (no radiators required) or just for floor warming. At 200watts per sqm it is suitable for all rooms under wood & laminate and is ideal for high heat loss areas including conservatories without the need of additional heating. Please note: Heat film mats are a bespoke product and we will need mat sizes or a dimensional drawing from you as with out this we will not be able to process your order please see below for more details.
The perfect heating system requires. Thing to know about this product.Our heat film comes in 0.5m, 0.8m and 1m widths, which we then cut to your required length in 250mm increments to suit your floor. Wall to wall internal measurements. And we can work out a floor plan illustrating how the mats will be situated for you to confirm. Please note to use this heating effectively and efficiently you will require our Impact Plus thermal insulation or (Soft Insulation) for use under this heating.
You will also require sufficient insulation to cover your total floor area not just your heated floor area so that you maintain an even floor, for your floor covering. When installing this heating under vinyl, the vinyl must be suitable and not rubber backed. And our duo overlay layer will replace your underlay ready for the vinyl to be fitted over. This heating is very easy to fit with no experience or specialist tools required, however the heating must be wired through an RCD and the final connections must be carried out by a qualified electrician. For areas over 3600watts a relay switch /contactor may have to be incorporated to carry loads over over 16amps.
200w Carbon film heating element. Suitable under wood and laminate floors. Fit into a standard 1 gang back box. And can carry a maximum load of 16amps. After this threshold is passed a simple contact or relay switch must be installed.Monitors the temperature of your floor. For a very accurate temperature reading. The floor probe comes at a standard 2.5m in lenght and if required can be extended on site.
Supplied to assist in holding mat or cable in position if needed when installing the underfloor heating system. Our comprehensive fitting instructions leave no stone unturned.
Offering you a step by step instruction manual. How to Install underfloor heating carbon film mats.Under Wood & Laminate a Fitting Instructions for carbon film Underfloor Heating Systems. Floor Preparation / Laying of Insulation. The concrete or wood sub floor should be stable, clean and suitable for the desired floor covering, prior to any underfloor heating being installed. Once the floor is prepared, start by rolling your insulation out over the sub floor making sure to cover the total floor area where the wood, laminate or vinyl floor covering is to be laid including unheated areas. A contact spray adhesive can be used or a double sided tape to hold the insulation in place if required but is not a necessity.
The diagram below shows the soft insulation being installed with the floor sensor / probe fixed in place. Once you have decided on the mat layout within your room you will first need to install the floor sensor supplied with your thermostat. Cut a small channel into the insulation layer to allow the floor sensor / probe to be laid into.
The channel should be located under a heated area, (heat mat to be laid over this channel in next stage). Laying Underfloor Heating World (Living Heat) film mats.
If you have requested a proposed mat layout from Living Heat you can simply hand this to the installer or follow the plan yourself. Make sure you unroll and identify each mat, Start at one side of the room rolling the mats out in a structured way making sure not to overlap any mats at any point.
Each mat can be held in place by using a suitable adhesion tape such as gaffa tape along the ends and side of the mats. Once the mats have been laid and fixed in place the connection tails should be run back to the thermostat / junction box location. The connection ends and cold tails can be pressed into the insulation by scoring the insulation and firmly pressing the tails / ends into the scored insulation. It is advisable to tape over the connection tails and cold ends to keep them held in place during the instillation of your wood / laminate floor. The diagram below shows the two ways mats can be connected beck to the thermostat.
(Mats must always be connected in parallel never in series). Once the underfloor heating world (Living Heat) mats have been laid and fixed in place the vapour barrier is ready to be laid over the top of all the under floor heating mats. The vapour barrier, (Supplied free with all heating mats), must fully cover all under floor heating mats, (it is not a necessity to cover the whole floor area only the actual heat mats themselves). If necessary the vapour barrier can be taped around the edges to hold it in place.
Underfloor heating world (Living Heat) heat film is designed for use directly under all wood and laminate floors, (vinyl must be good quality and not rubber backed). Please note it is advisable to regulate the floor temperature using the floor probe with the thermostat set to floor only. This is because all wood & laminate floors have different max permitable temperatures and thus the flooring supplier should be consulted first to confirm the max permitable floor temperature the heating can be set to. This tends to be approximately 28oc for most wood & laminate floors.A qualified electrician should be used to make the final connections to the mains power. This heating is not suitable for wet areas such as bathrooms / wet rooms. To make sure you receive the correct sizes, if you are unsure of what you require, please do not hesitate to contact ourselves. If possible please provide us with a sketch or measurements of the floor area you would like covered and we will advise you on which product would best suit your requirements. Our technical information and installation guides can be found on our websites. During busy periods we can not guarantee your packages will be sent out same day. To minimise any delays please make sure you provide us with a valid telephone number. Our couriers try their best to deliver next day and currently have a 98% success rate. All our deliveries can be tracked so don't hesitate to ask one of the staff who will be happy to help. Please note: liquids cannot be sent to international addresses due to current aviation regulations. Please make sure the goods are sent back in good working order and in the original packaging.
(please do not forget to include a note with your name, address and copy of your original invoice if possible). The item "Underfloor Heating Kit For Under Laminate and Wood Floors + Digital Thermostat" is in sale since Thursday, September 15, 2011. This item is in the category "Home, Furniture & DIY\Heating, Cooling & Air\Air Conditioners & Heaters\HVAC Parts & Accessories". The seller is "livingheat-underfloor-heating" and is located in Torquay, Devon.
This item can be shipped to United Kingdom, Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech republic, Denmark, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Australia, United States, Canada, New Zealand, Norway, Mexico, Switzerland, Bermuda, Iceland, Liechtenstein, South africa, Chile.