Portway Arundel 4.9kw Defra Approved Woodburner Multi Fuel Stove & Complete 9m Liner Install Kit! This listing includes a Portway Arundel 4.9kw Multi Fuel Stove and a complete installation kit including 9m of 6" 150mm flexible flue liner and a complete accessory pack of 1 x 5" 125mm 1m length of vitreous enamel matt black flue pipe 1 x 5"-6" 125mm-150mm Flexible flue liner adapter 1 x 1kg tub of black fire cement 1 x 6" 150mm Flexible flue liner nose cone 1 x Chimney notice plate 1 x 6" 150mm Hanging/suspending rain cowl 1 x 800mm x 400mm Register plate kit inc 5 reducing plate.This kit includes everything needed to enable the installation of the Portway Arundel stove & 6 Multi Fuel flexible liner into a masonry chimney where the chimney pot is not going to be removed. This saves the hassle of trying to remove the existing pot and is also a big time saver. Full Details Of Kit Contents Are As Follows. Portway Arundel 4.9kw Multifuel Wood Burning Stove.
The Portway Arundel Stove has been developed with aesthetics, efficiency and flexibility in mind. This steel bodied stoves robust looks and large viewing window makes it suitable for most room settings.The Portway Arundel has a heat output of 4.9kW and an efficiency of 78.4% allowing it to be both cost effective and heat efficient. The Arundel is suitable for use in Smoke Control Areas, as recommended by DEFRA. Strong steel body and door. Max Log Length (mm): 250. Simple primary and secondary air controls. Large viewing window 285mm x 270mm. Suitable for use in Smoke Control Areas, as recommended by DEFRA. 5 125mm 1m Matt Black Vitreous Enamel Flue Pipe. A straight pipe section 1000mm long with socket facing upward and spigot facing down used for connecting the appliance to the flue liner.
5"-6" 125mm-150mm Flexible Flue Liner To Single Skin Adapter. Used to connect the flexible flue liner to single wall flue pipe at the base of the flue. The hole on the inside of the adapter allows any moisture and deposits to run into the inside of the pipe instead of escaping down the outside of the pipe. Connects 6" single wall flue pipe to 6" flexible flue liner. 1Kg Tub Of Black Fire Cement.A black in colour adhesive fire cement withstands 1200°C and is used to seal joints between flue components. 9m 6 150mm 316Grade Flexible Flue Liner. If you don't know what flexible Flue liner is it used for relining existing chimneys which have wood burning Stoves and Open Fires our Flexible Flue liner is a twin skin liner suitable for use on Gas, Oil and Multi fuel appliances, where the maximum flue gas temperature does not exceed 600°C. Both inner and outer skins are made from 316 grade stainless steel which is highly anti corrosive our liner has an overlapped design which means that it has very high strength and anti corrosion qualities but this does also mean that the liner inside is smooth to the touch one way and ridged the other so it is important that it is installed the correct way. There is a arrow printed on the outside which needs to be pointing up to help with the installation. 6 150mm Flexible Flue Liner Nose Cone.
The nose cone is attached to the end of the liner and provides protection to the end of the liner during installation and also aids installation by being able to attach a draw cord to the liner. Chimney Notice plate is now a Building Regulations requirement.
They must be filled out and fixed near to the appliance or within a meter cupboard. 6 150mm Hanging/Suspending Rain Cowl Inc Bird Guard. This cowl not only allows the chimney liner to be installed without removing the pot, but prevents any birds accessing the chimney but also has increased rain protection.
It is fixed to the top of the pot and takes/supports the weight of the liner below, simply push the liner between the three straps and tighten the supplied jubilee band. The cowl also has further straps which hang down the outside of the chimney pot.
The jubilee band supplied is fixed around these to secure against the pot. 800mm x 400mm Register Plate Kit. Use to seal off the base of the chimney (This Register Plate can be cut on site to fit the base size of your chimney stack).The Register Plate will support vermiculite insulation and stop any debris from within the chimney stack coming down the chimney and hitting your stove. The Register Plate and the Supporting Brackets are made from 1.5mm thick galvanised steel. The Register Plate can be sprayed to match the colour of your stove pipe.
This Register Plate has a special adapter suitable for installations which use either 125mm or 150mm diameter flue pipes. This is everything that is needed to install the Portway Arundel stove into a masonry chimney stack with a chimney pot in place. The item "Portway Arundel 4.9kw Woodburner Multi Fuel Stove &Complete 9m Liner Install Kit" is in sale since Sunday, October 29, 2017.This item is in the category "Home, Furniture & DIY\Fireplaces & Stoves\Heating Stoves".f_supplies" and is located in st columb road, , Cornwall. This item can be shipped to United Kingdom, Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Australia, United States, Bahrain, Canada, Brazil, Japan, New Zealand, China, Israel, Hong Kong, Norway, Indonesia, Malaysia, Mexico, Singapore, South Korea, Switzerland, Taiwan, Thailand, Bangladesh, Bermuda, Bolivia, Barbados, Brunei darussalam, Cayman islands, Ecuador, Egypt, Guernsey, Gibraltar, Guadeloupe, French guiana, Iceland, Jersey, Jordan, Cambodia, Liechtenstein, Sri lanka, Macao, Monaco, Maldives, Martinique, Nicaragua, Oman, Pakistan, Peru, Paraguay, Reunion, Saudi arabia, South africa, United arab emirates, Ukraine, Bahamas, Colombia, Jamaica, Kuwait, Panama, Qatar, Uruguay, Viet nam.